IET/QuadTech 1910 Inductance Analyzer

  • Now Manufactured by IET Labs
  • 20 Hz to 1 MHz Frequency Range (27,000 Possible Test Frequencies)
  • 0.1% Basic Measurement Accuracy
  • Measures 15 Impedance Parameters, DC Resistance, Voltage and Current
  • Wide Measurement Range with 5 Digit Measurement Resolution
  • Four-terminal Kelvin connections to maintain measurement integrity
  • AC Test Voltage Programmable from 20 mV to 1V
  • CE Marked
Priced at
$5,125.00


The 1910 Inductance Analyzer is designed to perform inductance and impedance measurements on coils and wire wound devices over a frequency
range from 20Hz to 1MHz. Emphasis has been placed on ease of use through menu programming, and fast accurate production testing via its remote control capability.

15 Different Impedance Parameters/20 Total Parameters Measure and display any two parameters simultaneously, to achieve coverage
and flexibility not previously available.
Automatic Test Sequencing Run up to six different tests in sequence with a single push of the start button. Each test can have different conditions and limits.
Program and Data Storage Test setups can be stored and recalled from internal memory. The front panel can be locked out, with password protection, to ensure procedures are run the same way every time.
Load Correction Substantially improves instrument accuracy by performing measurements on a known standard and applying correction to subsequent measurements. Ideal for repetitive testing of identical devices at like test conditions.


Why Buy The 1910 1MHz Inductance Analyzer?

  • For a wide frequency range (to 1MHz) at an affordable price
  • When both AC impedance and DC resistance measurements are needed
  • For automated production testing using RS232, IEEE-488 & PLC interfaces
  • When internal bias current is required for testing coils and inductors
  • Configure instrument and log results to PC using the 1900 Virtual Front Panel

If you are looking for a more cost effective or higher preforming LCR Meter See our LCR Meter Selection Guide

1910 Inductance Analyzer Basic Specifications

Measured Parameters and Basic Measurment Accuracy:

Parameter Measurement Range Fast Medium Slow
Ls,Lp 0.001 nH to 99.999 H +/-0.5% +/-0.25% +/-0.1%
Cs,Cp 1 pF to 9.9999 F +/-0.5% +/-0.25% +/-0.1%
DF 0.00001 to 99.999 +/-0.005 +/-0.0025 +/-0.001
Q 0.00000 to 9999.9 +/-0.005 +/-0.0025 +/-0.001
Y,Gp,Bp 10 nS to 9999.9 S +/-0.005 +/-0.0025 +/-0.001
|Z|,Rs,Rp,Xs,ESR 0.0001 mΩ to 99.999 MΩ +/-0.5% +/-0.25% +/-0.1%
Phase Angle -180.00 to +179.99 degrees +/-1.8° +/-0.9° +/-0.18°
DCR 0.1 mVto 100 KV +/-0.5% +/-0.25% +/-0.1%
DUT AC Voltage 20 mV to 1.0 V +/-0.5% +/-0.25% +/-0.1%
DUT AC Current 1 μA to 150 mA +/-0.5% +/-0.25% +/-0.1%
DUT DC Voltage 20 mV to 1.0 V +/-0.5% +/-0.25% +/-0.1%
DUT DC Current 1 μA to 150 mA +/-0.5% +/-0.25% +/-0.1%

*At optimum test signal levels, frequencies, DUT values and without calibration uncertainty. Capacitance (Cs/Cp), Inductance (Ls/Lp), Resistance (Rs/Rp), Dissipation (D) and Quality (Q) Factors, Impedance Z , Admittance Y , Phase Angle (0-), Equivalent Series Resistance (ESR), Conductance (Gp), Reactance (Xs), Susceptance (Bp) Note: s = series, p = parallel, ESR equivalent to Rs
Test Frequency Range: 20Hz to 1MHz, Continuous
Test Frequency Resolution: 1Hz from 20Hz to 1kHz, 4 digits >1kHz
Test Frequency Accuracy: +/- (0.01% +0.02 Hz)
Measurement Speed: Fast: 40 meas/sec Medium: 8 meas/sec Slow 1 meas/sec
Ranging Automatic,Range Hold or user selectable
Trigger internal (automatic) External(via RS-232,IEEE-488.2 or Handler interfaces Manual
Source Impedance 5V, 25V, 50V, 100V, or matched impedance, range dependent
AC Test Signal Voltage: 20mV to 1.0V (open circuit) in 5 mV steps
DC Bias Current Internal: 0.0 to 1.0A in 1mA steps External: up to 20.0A
Standard Interfaces IEEE-488.2 • RS-232 • Handler • Serial Printer
Measurement Delay Programmable from 0 to 1000 ms in 1ms steps
Averaging Programmable from 1 to 1000
Median Value Averaged over last three measurements
Built-in automatic calibration procedure
Test Terminals Front panel, four terminal (BNC) Optional Test Fixtures Available
Dimensions: 17x 5.25x 16in (432x 133x 406 mm)
Weight: 15lbs (8kg) net, 21lbs (9.9kg) shipped